New Gas-Lift Pilot Valve Increases Gas-Lift Efficiency (Record no. 130842)

MARC details
000 -LEADER
fixed length control field 03440nmc a2200301 4500
008 - CÓDIGOS DE INFORMACIÓN DE LONGITUD FIJA - INFORMACIÓN GENERAL
Campo de control de longitud fija 260224s2001 xxu ing
041 ## - IDIOMA
Idioma Inglés
245 00 - TITULO
Título New Gas-Lift Pilot Valve Increases Gas-Lift Efficiency
Subtítulo SPE 69402
260 ## - PUBLICACION, DISTRIBUCION, ETC
Lugar de publicación, distribución, etc. Dallas, Texas
Nombre de publicador, distribuidor, etc. Society of Petroleum Engineers
Fecha de publicación, distribución, etc. 2001
270 ## - FECHA DE CARGA
Fecha de carga 12/09/06 ; 17/07/01
520 ## - RESUMEN, ETC
Resumen The most important component in an intermittent gas lift installation is the pilot valve. Its selection and proper calibration determine the success of the gas lift design. Recent tests performed in a field scale installation equipped with an experimental well and careful observations of the performance of real wells on intermittent gas lift in Lake Maracaibo have shown the importance of the proper selection of the area ratio of the pilot section and the main port diameter. Usually, the designer has a variety of area ratios of the pilot section to choose from and its selection will depend on the type of gas lift operation, choke controlled or use of time-cycle controllers, and the volume of gas needed per cycle. In some cases, the lowest commercially available area ratio will still be too large with the result of not being able to inject below a certain volume of gas per cycle. The over-injection per cycle takes place because the minimum spread attainable is greater than needed. This situation occurs when the tubing-casing annulus is large and the valve size that can be installed in the well is smaller than the 1 ½-inch valve. Hundreds of wells in Lake Maracaibo with 7-inch casings and 2 7/8-inch tubing can not be efficiently lifted because of the lack of commercially available pilot valves with small area ratios. The diameter of the main gas injection orifice is a fixed value for a particular valve model. The size of this orifice is important for two reasons: The size of the injection orifice, together with the injection pressure and tubing load, determines the velocity of the liquid slug being lifted. If the size of the orifice is too small, which is usually the case for 1-inch size valves, the liquid fallback is increased due to low liquid slug velocities. Small injection orifice diameters increase gas injection time and therefore limit the liquid production of the well, especially if the optimum cycle time is of short duration. Tests performed in an experimental well, and presented in this paper, show how a new 1-inch pilot valve design was able to increase the gas lift efficiency. The main features of the new gas lift valve, its calibration procedure and its performance in several real wells are also presented in this paper.
942 ## - DESC. DE MATERIAL
Tipo de item KOHA Congresos (trabajos presentados)
100 1# - RESPONSABLE PERSONAL
Apellido, Nombre Hernandez, Alí
9 (RLIN) 5767
100 1# - RESPONSABLE PERSONAL
Apellido, Nombre Perez, César
9 (RLIN) 5775
100 1# - RESPONSABLE PERSONAL
Apellido, Nombre Villalobos, Balmiro
9 (RLIN) 5776
100 1# - RESPONSABLE PERSONAL
Apellido, Nombre Romero, Analis
9 (RLIN) 5777
100 1# - RESPONSABLE PERSONAL
Apellido, Nombre Wildman, Sam
9 (RLIN) 5778
111 2# - AUTORIDAD DE CONGRESO
Nombre de congreso Latin American and Caribbean Petroleum Engineering Conference (7th : 2001 mar. 25-28 : Buenos Aires, Argentina)
9 (RLIN) 5738
700 1# - OTRA AUTORIDAD PERSONAL
Nombre Perez, César
9 (RLIN) 5775
700 1# - OTRA AUTORIDAD PERSONAL
Nombre Villalobos, Balmiro
9 (RLIN) 5776
700 1# - OTRA AUTORIDAD PERSONAL
Nombre Romero, Analis
9 (RLIN) 5777
700 1# - OTRA AUTORIDAD PERSONAL
Nombre Wildman, Sam
9 (RLIN) 5778
711 2# - ENTRADA AGREGADA--NOMBRE DE REUNIÓN
Nombre de congreso/reunión o jurisdicción como elemento de entrada Latin American and Caribbean Petroleum Engineering Conference (7th : 2001 mar. 25-28 : Buenos Aires, Argentina)
800 1# - RESPONSABLE EDICION
Nombre Hernandez, Alí
9 (RLIN) 5767
856 ## - LINK
Link <a href="https://biblioteca.iapg.org.ar/ArchivosAdjuntos/LACPEC2001/Spe69402.pdf">https://biblioteca.iapg.org.ar/ArchivosAdjuntos/LACPEC2001/Spe69402.pdf</a>
711 2# - ENTRADA AGREGADA--NOMBRE DE REUNIÓN
-- 5738
Holdings
Biblioteca propietaria Biblioteca actual Fecha de adquisición Inventario Total de préstamos Inventario Fecha de carga Tipo de item KOHA
Biblioteca virtual Biblioteca virtual 03/03/2026 200002885   200002885 03/03/2026 Archivo electrónico


Instituto Argentino del Petróleo y del Gas
Maipú 639 (C1006ACG) – Buenos Aires – Argentina
Tel: (54 11) 5277 IAPG (4274)
Lu - Vie 11 a 17 hs
Mail: biblio@iapg.org.ar


Copyright © 2026, Instituto Argentino del Petróleo y del Gas, todos los derechos reservados.

Protección de datos personales